Some days back I setup a LAN at my home between two PCs and one of them DOESN’T have a LAN card! PC1 has Ethernet card but PC2 doesn’t. I used BSNL’s broadband modem (router) to connect them. (Those not in India maynot know about BSNL). My router is Huawei SmartAX MT882. It has ports for both USB and ethernet. Basically when using USB u r required to install the router’s drivers and this installs a software dslagent. Now the router will appear as a LAN card to the computer.
Steps to setup this:-
—————————
1) router’s ethernet port was connected to PC1’s ethernet card, and the USB port was connected to USB of PC2.
Follow these steps for both PC1 and PC2.
2) Goto ControlPanel->NetworkSetUp Wizard (note for SP1 this option is available only in Network Connections as Set Up home or small office network).
3)Click Next 2 or 3 times and AT a page Choose ‘This computer connects to the internet through a residential gateway or through another computer on my network.’
4)Enter comp description and comp names (Note the names of both the pcs should be different).
5)Let the workgroup name be MSHOME
6)Turn on File and Printer Sharing.
7)Now click next and finish.
8)Right click on drives or folders u want to share in both the comps and choose Sharing and security. Click the threatning looking link there. U may need to click on one or two threatning links and the u maybe be shown a dialog; Click Just turn on file sharing. Now u have two check boxes-> Share this folder on network AND ->Allow network users to change my files. Turn the 1st one on. Turn the 2nd one on only if u want that files from that folder to be changed from the other pc. NOTE: any file deleted on say PC1 from within PC2 wil delete that permanently, so beware!
When the folder has been successfully shared then a hand will appear superimposed on the folder icon.
Now u can start accessing them from My Network Places>View Workgroup Computers. Wait for some time. Now both the comps should appear there and u should be able access the shared folder by double clicking and getting inside them.
Troubleshooting:-
——————
Problem1:-
======
If u have installed 3rd party firewall like ZoneAlarm, then, when u click View Workgroup Computers, if u r greeted by an error message like Path not found. Access Denied or somthing like that then its maybe ur overprotective firewall’s deed.
Solution for ZoneAlarm: U should be using the LAN connection for internet hence it will be in Internet Zone.
1)First note down the IP address and subnet mask of this LAN connection. (for this goto Network Connection>Single click on that LAN connection’s entry. See the Details section there).
2)Goto ZA’s control centre>Firewall>Zones>Click on ‘Add>>’>Subnet
3)Choose Trusted for Zone. Enter the just noted IP address and subnet mask there. Enter anything for Description.
Done!
Note: When ur router will connect to the BSNL’s server then the IP of ur card may change and hence all the above troubleshooting u did may fall flat on its face. In that case just TURN OFF ur FIREWALL.
Problem2:-
======
The comps in the View Workgroup Computers sections shows fine but when u try to double click on the other PC’s icon then u get error.
Solution: Try typing the url to the shared folder in the addressbar of the folder. Like this:-
\\the PC name\the shared folder or drive’s name
\\homePC\D\
A useful tip:-
————-
U can make the shared folders or drives show up as drives on ur comp. Open My computer>Tools>Map Network Drive>in Folder field type url to your folder as shown above.
Now a new drive of type Network Drive will appear in MyComputer of Drive letter starting form Z:
U can follow it up at the forum where I have posted it.
Disclaimer:-
————-
Any harm done to ur comp due to following this tip is not my reposibility. Please don’t try to burden my conscience with ur accusitions later for screwing up ur network settings.